22 diamond ? construction hardware lashed cable supports lashed cable supports ? used to strap coaxial and telephone cable to strand. ? available in 430 stainless steel or special zinc alloy in 3/4width. ? edges are processed to remove raised and projecting metal. edges are smooth and free from burrs. part number length diameter bundle circumference inner pack outer pack zinc stainless steel 34-08911 34-08912 10" 1.2" 3.8" -- 500 34-08921 34-08922 16" 2" 6.3" -- 500 34-08931 34-08932 22" 3" 9.4" -- 300 34-08941 34-08942 28" 4" 12.6" -- 300 34-08951 34-08952 34" 5" 15.7" -- 300 * 34-08956 45" 6.5" 20.4" -- 200 34-08961 * 50" 7.5" 23.6" -- 200 * 34-08972 66" 10.0" 31.4" -- 200 * 3408972-sp 66" 10.0" 31.4" -- 200 installation: 1. measure diameter or circumference of bundle. use table to determine strap length. 2. thread strap through spacer slot. 3. wrap strap around bundle (strand, spacer, cables) then through buckle twice, pulling eachwrap tight. 4. strap end should be doubled under itself (about 1.5) before making fnal pass through buckle. trim off excess. 5. bend doubled thickness over top of buckle to prevent unravelling. note: in cable tv installation, straps should not be too tight as they may restrict cable movement during contraction and expansion and possibly damage cable. 1 2 3 4 5 * ask ppc/belden representative. www.ppc-online.com customer support: 800.800.6652 a belden brand a belden brand
23 diamond ? construction hardware lashed cable supports lashed cable support kit ? used to strap coaxial or telephone cable to strand. ? kit contains 100 ft. 430 stainless steel strapping and 75 steel buckles. ? kit makes 75 straps 16 average length. ? cut to desired length and secure to buckle. plastic cable spacer ? high density outdoor polyethylene with u.v. inhibitors. ? bell type. ? provides separation between aerial cable and messenger. support strap ? reusable support strap with integral buckle made of malleable aluminum fre retardant. used to bundle telephone, coaxial and fber cable at the steel strand. ? safe to use, no sharp edges to cut hands or cables. part number description inner pack outer pack 34-00890 3/4" wide stainless steel strap with 75 buckles 1 10 part number description inner pack outer pack 34-08850 1/2" plastic spacer 100 1,000 34-08875 3/4" plastic spacer 100 1,000 part number description inner pack outer pack sc05-1 10" long, 3/4" band -- 500 sc06-1 16" long, 3/4" band -- 500 construction hardware a belden brand customer support: 800.800.6652 www.ppc-online.com
24 diamond ? construction hardware clamps lashing clamps ? used to secure lashing wire terminations. ? mechanically galvanized astm b695. ? 1/4 - 7/16 clamp range. part number description inner pack outer pack sc07-1 lashing clamp -- 100 26-09010 "d" lashing clamp -- 100 26-09010ns "d" lashing clamp no stakes -- 100 26-09020 "e" lashing clamp -- 100 26-09022 "e" lashing clamp with 2 washers, 2 nuts -- 100 figure 8 three bolt suspension clamps ? used to secure figure 8 cable to pole. ? center hole accommodates 1/2 or 5/8 diameter machine bolt. ? clamp plates aluminum alloy. ? steel bolts mechanically galvanized astm b695. ? eliminates need to strip messenger. part number description messenger size range inner pack outer pack 28-09610 figure 8 three bolt suspension clamp .109" - .134" -- 25 28-09615 figure 8 three bolt suspension clamp .148" - .250" -- 20 figure 8 tangent support clamps ? used to secure figure 8 cable to pole. ? clamp plates and j hook aluminum alloy. ? eliminates need to strip messenger. part number description thru bolt hole size messenger size range inner pack outer pack 28-09500 tangent support clamp 5/8" .148"-.250" -- 25 28-09600 tangent support clamp 1/2" .109"-.134" -- 25 28-19651 tangent support clamp 5/8" .109"-.134" -- 25 26-09020 26-09010 www.ppc-online.com customer support: 800.800.6652 a belden brand a belden brand
25 diamond ? construction hardware hangers, brackets, hooks fiber optic rack hanger ? secures f.o. storage devices (snow shoes) to strand. ? for 1/4 - 7/16 strand. ? aluminum bracket. ? steel astm b695 clamp plates. dead-end bracket ? dead-end bracket used to apply tension to steel strand building riser and to provide a means to dead-end a guy strand. ? mechanically galvanized astm b695. ? 1,000 lb. load capacity. drive hooks ? used to support bail-type drop wire clamps to poles. ? galvanized to astm a153 or b695. ? fetter drive threads. part number description inner pack outer pack 29-19945 fiber optic rack hanger -- 25 part number description inner pack outer pack sc44-1 5/16" diameter hook with 2-3/4" tension adjustment -- 25 part number description inner pack outer pack 40-43007 7/16" diameter x 4-3/4" long -- 100 40-43008 5/16" diameter x 3-1/2" long -- 200 square washer ? supports bolt head or nut of machine bolt. ? mechanically galvanized astm b695. part number description inner pack outer pack 28-03004 5/8" bolt size x 2-1/4" square x 3/16" thickness -- 100 construction hardware a belden brand customer support: 800.800.6652 www.ppc-online.com
26 diamond ? construction hardware tap brackets tap brackets ? used to secure tap to strand. ? one piece steel snap-on version mechanically galvanized astm b695 for 1/4 strand only. ? aluminum standard tap bracket & extension bracket. both have 1/4 to 3/8 strand clamping range. ? square hole in standard aluminum tap bracket mounts diamond trap sleeve brackets (wbrackets). part number description clearance between strand & tap load capacity (lbs) (minimal deflection) inner pack outer pack 29-19941 steel snap-on tap bracket 2-1/2" 40 -- 25 29-19943 aluminum tap bracket (standard) 2-1/2" 30 -- 25 29-19944 aluminum extension bracket 3" to 9" 25 -- 25 29-50044 strand clamp -- -- -- 75 tap bracket with common ground ? tap bracket used to secure a tap to the steel strand and provide a means to bond up to eight messengered drop cables. ? firm and positive grip with no rotation or sliding on steel strand. ? mechanically galvanized astm b695. part number description inner pack outer pack sc23cgs-4 4" horizontal mounting with 8 common grounds -- 32 29-19941 29-19943 29-19944 tap bracket - vertical mount ? tap bracket used to secure a tap to the steel strand. ? firm and positive grip with no rotation or sliding on steel strand. ? stopper at multi-tap attachment prevents part rotation. ? mechanically galvanized astm b695. part number description inner pack outer pack sc23pv-2 2" vertical mount (figure 8 application) -- 32 sc23pv-4 4" vertical mount (figure 8 application) -- 32 29-50044 www.ppc-online.com customer support: 800.800.6652 a belden brand a belden brand
27 diamond ? construction hardware tap brackets, support brackets tap bracket - horizontal mount ? tap bracket used to secure a tap to the steel strand. ? firm and positive grip with no rotation or sliding on steel strand. ? stopper at multi-tap attachment. ? mechanically galvanized astm b695. part number description inner pack outer pack sc23ps-2 2" horizontal mount -- 32 sc23ps-3 3" horizontal mount -- 32 sc23ps-4 4" horizontal mount -- 32 sc23ps4-c 4" horizontal mount - canada -- 32 strand hanger support bracket ? used in mid-span or next to tap application. ? in high risk theft areas, makes it more diffcult to tamper with the traps. ? support up to 4 trap shields (up to 16 traps). ? mechanically galvanized astm b695. ? can also be supplied with a coated top shield aluminum bracket. part number description inner pack outer pack sc73-1f strand hanger support bracket -- 32 construction hardware a belden brand customer support: 800.800.6652 www.ppc-online.com
28 diamond ? construction hardware aerial cable damper aerial cable damper part number description inner pack outer pack 28-80001 aerial cable damper -- 5 ? aluminum alloy. ? designed to use the force of wind to aerodynamically reduce oscillation of cable. ? supplied with special heavy duty lashed cable supports and d lashing clamps to secure to strand. ? assembly instructions provided. installation: 1. select proper size cable guard for application. 2. place guard on cable over horizontal slots in aerial cable damper (acd). 3. insert lashed cable supports through horizontal slots. use two wraps and secure by bending end over top of buckle. allow 1/4 clearance between cable and top of the acd. the acd must be allowed to swing free with the wind. 4. position lashing clamps inside lashed cable supports and secure. lashing clamps will restrict longitudinal movement to cable area protected by cable guards. 5. placement C the number of acds varies with the length of cable span and terrain. the following is recommended as a guide for maximum effectiveness. level ground C locate at spans center for 125-170 ft. spans (fig. 1). on spans 170-300 ft., locate two acds, each one-fourth the total span length from either pole. (fig. 2) steep grade C locate one-tenth total span length from pole at lower level on 125-170 ft. spans. (fig 3). on spans 170-300 ft., two acds are required. locate one at one-fourth the total span length from lower pole. locate second acd halfway between frst acd and uphill pole. (fig. 4). note: when installing on fig. 8 cable: 1. acd should be secured to exposed strand. 2. acd will have limited dampening effective in extreme high wind conditions. construction hardware www.ppc-online.com customer support: 800.800.6652 a belden brand a belden brand
|
